Home About Regus Agent Brands Products News Center Database FAQ & Services Contact Us
 
Bearing Categories
Deep Groove Ball Bearings
Self-Aligning Ball Bearings
Cylindrical Roller Bearings
Spherical Roller Bearings
Angular Contact Ball Bearings
Tapered Roller Bearings
Thrust Ball Bearings
Thrust Roller Bearings
Bearings Units Housings
Needle Roller Bearings
Spherical Plain Bearings
Other Special Bearings
 
Hot Products
 
  Deep Groove Ball Bearings
Deep Groove Ball Bearings

Manufacture a full range of deep groove ball bearings. These bearings are the most common type and are used in a wide variety of applications.

Single-Row Deep Groove Ball Bearings
Pressed Steel Cages
Single-row deep groove ball bearings are the most common type of rolling bearings. Their use is very widespread.
In addition to open type bearings, these bearings often have steel shields or rubber seals installed on one or both sides and are prelubricated with grease. Also, snap rings are sometimes used on the periphery. As to cages, pressed steel ones are the most common.
For big deep groove ball bearings, machined brass cages are used.
Machined cages are also used for high speed applications.


Extra Small Ball Bearings and Miniature Ball Bearings
Miniature and instrument ball bearings can be divided into two basic types, deep groove and angular contact. The first (deep groove) can be further divided into the following five classes depending on their design details:

Standard type
Flanged outer ring
Extended inner ring
Expanded type in which one ring has a radial thickness that is larger than normal compared with the bearing width.
Thin section type in which both rings are extra thin in the radial direction. They can also be classified as: open, shielded, or sealed. 

Maximum-Type Ball Bearings
Maximum-Type ball Bearings contain a larger number of balls than normal deep groove ball bearings because of filling slots in the inner and outer rings. Because of their filling slots, they are not suitable for applications with high axial loads. BL2 and BL3 types of bearings have boundary dimensions equal to those of single-row deep groove ball bearings of Series 62 and 63 respectively. Besides the open type, ZZ type shielded bearings are also available. When using these bearings, it is important for the filling slot in the outer ring to be outside of the loaded zone as much as possible. Their cages are pressed steel.


Magneto Bearings
The inner groove of magneto bearings is a little shallower than that of deep groove bearings. Since the outer ring has a shoulder on only one side, the outer ring may be removed. This is often advantageous for mounting. In general, two such bearings are used in duplex pairs. Magneto bearings are small bearings with a bore diameter of 4 to 20 mm and are mainly used for small magnetos, gyroscopes, instruments, etc. Pressed brass cages are generally used.

   
 
W 6306
W 6305
W 6304
W 6303
W 6302
W 6301
W 6300
W 627
W 626
W 625
W 623
W 6208
W 6207
W 6206
W 6205
W 6204
W 6203
W 6202
W 6201
W 6200
W 608
W 607
W 6008
W 6007
W 6006
W 6005
W 6004
W 6003
W 6002
W 6001
W 6000
6418
6417
6416
6415
6414
6413
6412
6411
6410
6409
6408 N
6408
6407
6406
6405
6404
6403
639213
639209
639177
639175
639174
639114
6386/Q
6386
635-2Z
635
634-2Z
634059
6334 M
6332 M
6330 M
6328 M
6326 M
6324 M
6324
6322
6321
6320
632
6319-Z
6319
6318-Z
6318
6317-Z
6317
6316-Z
6316
6315-Z

Total 6930 records7 NO.[1] [2] [3] [4] [5] [6] [7] [8] [9] [10] page 8


Copyright ©Regus Bearing LLC(Regus Bearing GmbH) All rights reserved.